Search found 19 matches

by Bellski
Wed Jun 19, 2019 2:06 pm
Forum: Electrical Troubleshooting, Maintenance, and Upgrades
Topic: HELP!! Anyone on?? 2.2 No start after pop sound gotta get to work
Replies: 9
Views: 308

Solved!!2.2 No start after pop sound gotta get to work

It was TOTALLY the fusable link wiring!!

Call Willie, I'm on the road again! Whew thanks!
by Bellski
Tue Jun 18, 2019 9:14 pm
Forum: Electrical Troubleshooting, Maintenance, and Upgrades
Topic: HELP!! Anyone on?? 2.2 No start after pop sound gotta get to work
Replies: 9
Views: 308

No start after pop sound

Sigh It's always the day when you're like, "at least my Pup loves me" lol Jack, I'm guessing if the POS terminal end of a fusible link (I have two blue wires with plastic ends on POS terminal) was a bit frayed that might just be "a bad enough connection at the wrong place"? That ...
by Bellski
Tue Jun 18, 2019 6:52 pm
Forum: Electrical Troubleshooting, Maintenance, and Upgrades
Topic: HELP!! Anyone on?? 2.2 No start after pop sound gotta get to work
Replies: 9
Views: 308

HELP!! Anyone on?? 2.2 No start after pop sound gotta get to work

Hi, I just went to start my decent running utterly reliable '81 pup daily driver ( glow plug 1x, glow plug 2x, (hot day, no need for 3) and turn key to start-- but instead of starting (rain shine heat snow ok) it lurched and made a horrible popping sort of sound. It then had absolutely no juice... J...
by Bellski
Sat Apr 20, 2019 7:28 pm
Forum: General Troubleshooting and Maintenance
Topic: front rotor/caliper install nightmare, safety?
Replies: 5
Views: 249

Re: front rotor/caliper install nightmare, safety?

I didn't even try wiggling those other directions but I will when I get home
by Bellski
Sat Apr 20, 2019 7:27 pm
Forum: General Troubleshooting and Maintenance
Topic: front rotor/caliper install nightmare, safety?
Replies: 5
Views: 249

Re: front rotor/caliper install nightmare, safety?

Wiggling the tire in and out from the top of the tire. We used brake lube and the other little small tube...
by Bellski
Fri Apr 19, 2019 3:53 pm
Forum: General Troubleshooting and Maintenance
Topic: front rotor/caliper install nightmare, safety?
Replies: 5
Views: 249

front rotor/caliper install nightmare, safety?

1981 4*4 diesel Pup, 15" Rodeo locking hubs. Hi, My partner just replaced my front brakes/rotors/calipers. Simple procedures he has been doing all his life. However: A previous owner had mismatched bolts all over the place and drilled some of the boltholes larger, as well as replacing the 14&qu...
by Bellski
Sat Jun 23, 2018 2:35 pm
Forum: Diesel - Troubleshooting and Maintenance
Topic: Timing was set high/CSD leak/black smoke: possible IP or other damage?
Replies: 13
Views: 1236

Re: Timing was set high/CSD leak/black smoke: possible IP or other damage?

I finally got it! Broke my trimmed down wrench, so took off cover plate underneath and the battery and with a lot of finagling finally got it.. cutting off the broken end to make a stubby wrench gave me the room i needed. The key to the rear bolt (done from above) was using a thin metal rod to slide...
by Bellski
Tue Jun 19, 2018 8:54 pm
Forum: Diesel - Troubleshooting and Maintenance
Topic: Timing was set high/CSD leak/black smoke: possible IP or other damage?
Replies: 13
Views: 1236

Re: Timing was set high/CSD leak/black smoke: possible IP or other damage?

Looks clearly like it was leaking at both spots but much more heavily at the pump juncture.
by Bellski
Tue Jun 19, 2018 8:53 pm
Forum: Diesel - Troubleshooting and Maintenance
Topic: Timing was set high/CSD leak/black smoke: possible IP or other damage?
Replies: 13
Views: 1236

Re: CSD leak repair

I have and am trying to do both but I can’t getthose last two bolts to get between the CSD and the pump body. *sigh* holy moly. The old flat half metal half rubber washer that was by the big spring in the CSD did not even have a lip on it anymore so hopefully that helps, but if i can’t get the other...
by Bellski
Tue Jun 19, 2018 1:01 pm
Forum: Diesel - Troubleshooting and Maintenance
Topic: Timing was set high/CSD leak/black smoke: possible IP or other damage?
Replies: 13
Views: 1236

Re: Timing was set high/CSD leak/black smoke: possible IP or other damage?

Well today is the day for the CSD gasket replacement....the tire is off, my wrench is ground down, the pictures well studied.....ok but frankly I am terrified.

But here goes.
by Bellski
Mon May 28, 2018 9:31 pm
Forum: Diesel - Troubleshooting and Maintenance
Topic: Timing was set high/CSD leak/black smoke: possible IP or other damage?
Replies: 13
Views: 1236

Re: Timing was set high/CSD leak/black smoke: possible IP or other damage?

Ok duly noted. Thank you. I still have do do a good engine bay clean before I can rule out any other leaks but I will take a pic even before cleaning just in case.
by Bellski
Sat May 26, 2018 11:37 pm
Forum: Diesel - Troubleshooting and Maintenance
Topic: Timing was set high/CSD leak/black smoke: possible IP or other damage?
Replies: 13
Views: 1236

Re: Timing was set high/CSD leak/black smoke: possible IP or other damage?

Putputtinpup: I will check that screw. I have a sneaking suspicion you may be right, as I considered the possibility of multiple leaks. Definitely keeping the CSD though, i change altitudes amd temps regularly. But good to know what to look for if I still have problems after leak and timing are reso...
by Bellski
Fri May 25, 2018 11:02 pm
Forum: Diesel - Troubleshooting and Maintenance
Topic: Timing was set high/CSD leak/black smoke: possible IP or other damage?
Replies: 13
Views: 1236

Timing was set high/CSD leak/black smoke: possible IP or other damage?

Hi everyone-- First off, It's important to start with two facts: bear with me here... 1.)While I am smart enough to have *always* wanted a little, insanely long lived, durable, efficient, mechanical dieseI truck (whoops I meant a P'up lol),I am as ignorant as most of you are brilliant at this stuff-...